#Loft angles for hogan irons professional
#Loft angles for hogan irons series

Thanks for this Richie, its pretty obvious that the components would have to be separated to find out what's really going on but what are you using for a 'standard'? If you're going by anything made today, even a set of forged blades its apples & oranges. Once again, thanks to Jeff Martin and the Think it is within reason that Hogan may have put an inordinate amount of weight His irons how stiff and difficult they were to hit. But if the weight was primarily located towards the butt end of the Very heavy static weight clubs that would be difficult to swing with any real ThatРІР‚в„ўs part of the problem with swingweight, Hogan may have had Would need to get a better idea of the total weight of the club and the MOI to His clubs also had a very light swingweight to them. So, HoganРІР‚в„ўs clubs with relation to todayРІР‚в„ўs standard were more like That for every Р’Р…РІР‚Сњ difference in shaft length. Hogan was only aboutР”ТђРІР‚в„ў6РІР‚Сњ tall, but he had no problem with making his clubs rather short in length.Р”В®ven back then, they were about Р’Р…РІР‚Сњ shorter than vintage iron However, I will assume that Hogan used theР”Р„nd here are the swingweights (based off the You can follow the thread at this link:Р”РЋ953 set had different lie angles than his РІР‚ВpracticeРІР‚в„ў set.

In particular a set of 1953 irons Hogan used and a If you have the head secured It's also important to position the bending bar as low as possible (where the hosel meets the head) and bend it at that position.Jeff Martin over at wasР’В able to get the measurements of Ben Hogan's irons from the USGA House. You can do this by setting the club with the leading edge flush to the ground and measuring the angle between the shaft and the floor with the protractor. After that you probably need to measure and check the new lie angle. Bending the hoselsР”ВonРІР‚в„ўt try to bend the clubs in one go, make multiple smaller bends until you feel that youРІР‚в„ўve got it right. If the head starts to twist in the vice it means that you didn't secure it in a way that resists the forces of the bending operation. The best way is to start by clamping the top line and the leading edge in the vice and try to bend the hosel. You need to find a way to secure it so that it won't move while bending. As you can see, I used 2 small metal plates to protect the club from damage. Securing the head in the vice is the tricky part. I donРІР‚в„ўt have a workbench in my apartment so I opted to bolt the vice onto some pieces of wood. If you have a workbench with a vice then thatРІР‚в„ўs great.

#Loft angles for hogan irons professional

Left to right: A professional loft and lie machine and a bending bar. Using a dedicated machine is much easier and faster than securing the head in a vice, but if you are on a budget you can get similar results using my method. Normally you would use a professional Loft and Lie machine for this purpose but since I donРІР‚в„ўt own one I decided to be creative. I bent these clubs 7 degrees flat and I did it using a bending bar, a vice and protractor. In this post I will describe the process of bending the lie angles of my Hogan irons. With cast irons the risk of breaking the hosel is far bigger and you probably will only be able to bend them 2 or 3 degrees tops. Forged irons can be bent more easily than cast irons. The lie angle, which is the angle between the shaft and the leading edge of the club head, may need to be changed as well depending on how flat or upright you want to swing the club. Vintage irons usually have weaker loft compared to modern irons, so you may want to bend those a bit stronger.

When youРІР‚в„ўre done with that you may want to change the loft and/or lie of your irons.

#Loft angles for hogan irons series

In the last installment of this series on restoring irons I wrote about regripping clubs.